The wrong way when someone has a paper jam problem is to lift the front cover and pull the jammed paper from the printer.

Therefore, follow the instructions below to find and remove the jammed paper (paper jam) from the printer properly. Before starting, make sure to follow each step correctly and don't skip the steps provided because it can potentially damage your printer.

Step One: Removing Paper From Printer Paper Tray

1. Remove all paper from the paper tray
2. Press the resume button
• If you were successful in clearing paper jams, skip to step 4 and make sure the carriage can move freely
• If the paper is still jammed continue to the next step
3. If more than one paper is jammed in the printer, remove the paper one at a time (remember through the printer paper tray). Hold the sheet in the middle of the pile with both hands and pull the sheet towards you. Usually, removing a sheet or two from the center of the pile takes the pressure off and can remove any paper jams.
4. After my friend has removed all the paper, check again that there are no scraps of paper / pieces of paper stuck in the printer.
• If you were successful in clearing paper jams, skip to step 4 and make sure the carriage can move freely
• If the paper is still jammed continue to the next step

In this article, we will share How to Reset Printer Canon IP 1980 and IP 1880. Many printer problems that often arise, sometimes these problems can be resolved by resetting the Eeprom Chip on the printer. The Canon IP 1980 printer must be reset if the printer experiences Ink Absorbser is full or ink tank full or an error appears on the printer such as:

1. Blink orange light 4 x and green 1 x
2. The orange and green lights flash alternately for 7 times
3. 8x blinking orange light

The steps to reset the printer canon IP 1980:

1. Make sure the printer driver is installed on your PC or laptop
2. Entering service mode (temporary reset) how to:
• Unplug the power cord
• Press and hold the power button on the printer
• The power button is still pressed, reconnect the power cable (the green light will light up)
• The power button is still pressed, press the resume button (the green light will turn off, the orange light turns on)
• Release both buttons at the same time (the printer will turn off)
• Restart the printer by pressing the power button on the printer (don't unplug the power cord)
3. Download the Canon IP 1980 printer resetter (General Service Tool) here
4. Extract the file that you have downloaded friend
5. Before running this general service tool program, make sure:
• If using Windows XP, make sure the computer / laptop screen resolution must be 1024 × 768
• If using Windows 7 or later, set the General Service tool compatibility file to Windows XP SP2
6. Run GeneralTool.exe
   
   
   
   
   
7. The USB port will automatically be detected by the program, if it is not detected, please select the USB port.
8. Check Cleaning and Eeprom Clear
9. Click the Main button then click the Platen button
10. Click the Quit button to exit the program
11. Turn off the printer by pressing the power button on the printer
12. Unplug the power cord
13. Reconnect the power cord then turn on the printer again by pressing the power button

Done. Please do a printing test. That was the troubleshoot on How to Reset the Canon IP 1980 Printer, hopefully this is useful.

Download Resetter Canon IP1980 Printer

Even though this Canon MP 237 printer is an old type printer, currently there are still quite a few users, as evidenced by the large number of our consumers who still use this Canon MP 237 printer for their daily printing needs. This multifunction printer is one of the best-selling printers in its class, with a new price of under 1 million, making the Canon MP 237 Printer which can be used for Print Scan and Copy friendly in the user's pocket.

This printer uses the same PG810 and CL811 cartridges as the Canon MP 287 and Canon IP 2770, whose price per cartridge is quite expensive, ranging from 185 thousand for the PG810 (black cartridge) and 240 thousand for the CL811 (tricolor cartridge), although most of these printer users make modifications by installing an infusion system. to reduce printing costs. as = cvwfc

Users of this printer sometimes encounter some errors on their printers, one of which is error P07 or E08 which appears on the LCD screen, and when it is used for printing, a notification will appear "The Ink Absorber is Almost Full". How to solve Error P07 or error E08 can be done by resetting the Canon MP237 printer.

How to Reset Canon MP237 Printer

1. Download the Canon V3400 Service Tool
2. Turn on your Canon MP237 printer
3. Enter into Service Mode how to:
• Turn off the Canon MP237 printer by pressing the power button
• Press and hold the STOP / RESET button then immediately press the power button and hold it down, so the RESET and POWER buttons are all pressed
• Release the button STOP / RESET POWER button do not release
• While the POWER button is still pressed, press the STOP / RESET button 6 times, no more or less
• When pressing the 6th STOp / RESET button, release the POWER button simultaneously by releasing the STOP / RESET button
• Your Canon MP237 printer is in SERVICE MODE
4. Extract the Canon Service Tool V3400 file that was downloaded the first step
5. Run the Canon MP237 Resetter (ServiceTool.exe) using a computer connected to the printer
   
   
   
   
   
6. On the Clear ink counter select main then click the set button
7. then on the Ink absorber counter select main also then click the set button
8. Click "EEPROM", then the printer will proceed by printing one page with the words "D = 000.0 ″
9. Turn off the Canon MP237 printer, friend, then turn it back on.
10. Do a test print. Done.

It's easy, fast and efficient, my friend can continue printing again, and hopefully your business will progress, the task will be completed soon, the job is easy. Hopefully troubleshooting How to reset the Canon MP237 printer is useful for all of you.

Canon Service Tool V3400 Free Download

The following is how to Reset Epson Printer L110, L210, L300, L350 or L355 series, either using the manual method (without application) or automatic reset using the latest version of the Resetter Adjustment Program (AdjProg.exe).

Almost all Epson Printer series (including the L110, L210, L300, L350 or L355 series) when there is an error (not wanting to print a document), usually the ink / paper indicator light will flash continuously or simultaneously repeatedly. An example is like the following picture.

In addition, various warnings will also appear on the computer monitor (PC / Laptop), such as "Ink pad is at the end of its service live", "Ink waste is full", "Service required", "it is nearly time to reset the ink levels "," it is time to reset the ink levels ", and other error messages.

Why did it happen? The answer is that there are many factors at play. Among them are printer components that have problems, the ink pad counter is full, the foam waste ink disposal pads are full, the maximum number has reached the limit and so on.

1. Check the Cause of the Error

When your printer gets one of these problems / error messages, don't panic first, let alone take the printer to a service worker. Because I'm sure you guys handle it easily, by doing a total reset.

In this case, to reset the Epson L110 L210 L300 L350 L355 printer there are two methods you can do. First manual reset (without application) and second automatic reset (using Resetter Adjprog.exe / Epson Adjustment Program).

But before doing the reset, you should check some parts of the printer which may be one of the main causes of errors or the paper / ink indicator light blinks continuously, including:

1. Ink Tube: Check the ink in the printer tube, if it runs out please refill.
2. Cartridge: Check printer cartridges. Make sure there is no dirt stuck to it and see its position, whether it is installed properly or not.
3. Roller: Make sure there is no paper jam in the printer roller.
4. Cable: Check the cable that connects the printer to the computer. Make sure both ends are securely attached.

If the things mentioned above have been done, but the printer is still not working, you should do a Total Reset, either manually or using the Epson L110 / L210 / L300 / L350 / L355 resetter adjustment program.

2. How to Reset Manual Without Application

Why does the Epson printer need to be reset? The reason is to return all settings to their original position and clean all data stored in the printer's IC Counter (EEPROM).

For example, returning the configuration to the initial position (default), resetting the maximum number of printed documents to zero, normalizing the ink pad counter, and so on.

Well, one of the easiest ways to reset the Epson L210, L110, L300, L350, L355 is to do a manual reset without any software / applications. For a guide on how to reset this manual, please refer to the steps below.

1. Unplug the power cord for about 3-5 minutes.
2. Turn it back on and wait for the printer to turn on perfectly.
3. Next, press and hold the resume button (ink logo) for 5 seconds, then release.
4. After that, press and hold the resume button again for 3 seconds, then release.
5. Shortly after that, the printer will automatically reset and wait for it to finish.
6. If successful, the indicator light will not flash and is ready to be used again.

But if the manual reset doesn't work and the printer indicator light is still blinking, then try doing an automatic reset using a special resetter adjustment program software.

3. How to Auto Reset Using Epson AdjProg Resetter

One of the first steps that must be taken before doing an automatic reset of the Epson L110 L210 L300 L350 L355 is to prepare the Resetter Adjustment Program software (Adjprog.exe). Now to get it, you can download it below for free along with a tutorial on how to use it.

3.1. Download Resetter Epson Adjustment Program

Adjustment Program / Adjprog.exe file

2.66 MB in size

Support Windows 7, 8, 8.1, 10 (32bit / 64bit)

Epson printers

L110 L210 L300 L350 L355 series

Download Adjprog.exe

Important Note: Before downloading the Resetter Epson Ajustment Program file above, please turn off your computer's Antivirus first (don't worry, because this file is not a virus).

Disclaimer: All forms of download files are only educational materials. The risks that may arise, please bear it yourself (Do With Your Own Risk).

3.2. How to Use Resetter Epson Adjustment Program

1. The first step you have to do is please download the Resetter Epson Adjustment Program file L210, L110, L300, L350, L355 above, then extract the file using the 7-Zip or WinRar application.
2. If so, the next step, please run the Epson Resetter Adjustment Program application by clicking 2X on the Adjprog.exe icon.
3. Click the [Select] button then select the printer model in [Model Name] and the USB port that is used, but it is better to choose [Auto Selection] only. After that click [OK].
   
   
   
   
   
4. Next, click [Particular Adjustment Mode] then select [Waste ink pad counter] then [OK].
   
   
   
   
   
5. In the next menu, tick on [Main pad counter], then click [Check]. At this stage, the printer will provide some important information about the printer, including how many times it has printed.
   
   
   
   
   
6. After that, tick again on [Main pad counter] and continue by clicking [Initialization]. Wait for the process to finish.
   
   
   
   
   
7. After the reset process is complete, the computer screen will display a notification [Please Turn On and Turn Off your printer]. Now at this stage, please turn off and then turn on your printer again.
8. Done. However, to further confirm whether the printer is back to normal, please try printing a document.

Usually, when the printer is properly set, there will be no more blinking on the indicator light and at this stage you can use it as usual.

This is the complete guide on how to do manual and automatic reset for the Epson L210, L110, L300, L350, L355 printers on this occasion, hopefully this will be useful for those of you who are looking for a solution to errors that occur on your printer. Good luck.

A printer that has an error can usually be found out by the appearance of a message that is displayed on your monitor screen. Besides that, we can also find an indication of an error on a printer with a blinking light and cannot print any documents.

Most error messages and problems with the printer not being able to print documents can be solved in a very easy and cheap way, by resetting the printer using simple software.

So before taking your printer to a service, it's a good idea to try resetting your printer first, because most problems that arise can be resolved by simply resetting.

To do this, please look carefully at step by step how to reset the following Canon MP287 printer.

Enter Canon MP287 Printer Service Mode

Before doing the reset process using software, we first have to condition the printer to be ready to reset, by entering the service mode manually by pressing a certain button on the printer.

• Make sure the printer is turned off and the power cable is not disconnected and still connected to the PC
• Press and hold the Stop / Reset button then press and hold the power button
• With the power button still pressed, release the Stop / Reset button then press it again 6 times
  
  
  
  
  
• Enter Service mode MP287
• Next, please release the two buttons
• The computer will automatically detect the new device

If your computer that is still connected to the printer has detected a new device or device, then you have succeeded in making the printer enter service mode and then just reset it using software. 

Reset Printer with resetter software

After successfully entering service mode, it's time to reset the printer using the resetter software as follows.

• Put 2 papers on the printer for test printing later
• Please download the resetter software on THIS LINK
• After downloading, please extract it
• Run the Service Tool v3400 on your PC by clicking 2 times
• Make the settings as shown below
  
  
  

• Usually the printer will print a test print
• Done

If you have done according to the steps we have described above correctly, usually the error or problem that arises will disappear and the printer can function normally to print, scan and copy documents.

If you experience failure in the reset process, try to repeat it by entering service mode again then continue with the reset using the service tool v3400, hopefully this time it can work.

However, if you have done the reset correctly and it turns out that the problem has not been resolved, it is possible that your printer malfunction occurs because there is a hardware problem so that further examination must be carried out by an expert.

My advice is to take your printer to the service center for further handling if it turns out that the error still appears after the printer has been reset properly.

You need to know that the Canon Pixma IP2770 / IP2700 Printer or any other Canon printer brand is usually made to do the initial setup after several uses. However, not everyone can do this initial setup for a Canon printer, maybe most people will take it to a printer service center. Okay, maybe that's a safe move. But if you want to try resetting the Canon printer yourself, here is how to reset the Canon iP2770 printer.

The first step:

1. If the printer is on, then turn off the printer first, but don't remove the power cable that is attached.
2. Press the RESUME button for about 2 seconds
3. Then press the POWER button until the green light flashes (when pressing the POWER button, don't release the RESUME button yet)
4. Slowly release the RESUME button but don't let go of the POWER button
5. While still pressing the POWER button, press the RESUME button 5 times. The led will turn on alternately orange and green with the last flame being orange.
6. After that, release both buttons simultaneously
7. The led will blink briefly after which it will turn green
8. Your computer or laptop will detect a new device, just ignore it
9. This situation indicates that the canon ip2770 printer is in SERVICE MODE and is ready to be reset.

 Besides service tool, you can use MPTool software to reset Canon printers MP series. This software support for canon MP150, MP160, MP170, MP180, MP450 and MP460. MPTool is portable software its small, light and  with easy to use feature and also its free. Besides reset counter functions this software resetter can be used to read, write and erase EEPROM on the Canon MP supported by this software.

On this software having all function to reset Canon MP150, MP160, MP170, MP180, MP450 and MP460 that is reset waste ink counter and reset ink level on the cartridge. Other excess MPTool, this software  can detect printer that installed on computer automatically. Here the features of MPTool software:

Reset Ink Level

Reset ink counter that is resetting ink level (ink meter) cartridge in printer.

• Turn on the printer to reset then run MPTool software
• Click Reset Black on Ink counter to reset ink level black cartridge or click Reset Color to reset ink level on the color cartridge.

Reset waste ink counter

To reset waste ink counter at printers canon pixma MP150, MP160, MP170, MP180, MP450 and MP460 there any 2 choice, that is :

• Start with printer on then run this software
• Click Reset Main (main) to reset waste ink counter and then click Reset Platen button (additional)

Althouh Resetter Canon MP145 at this not available but you can use manual reset to Reset Canon MP145. I get from forum but I’m not try this reset methode on Canon MP145, just sharing for other that require reset procedure for Canon Pixma MP145 to reset counter on this Canon Printer. This reset method also can be used to reset Canon MP150 and Canon MP160. Canon Pixma MP145 is multifunction inkjet printer with Scanning, printing and copying features. Canon PIxma Mp145 using canon Cartridge PG40 and Cl41. this cartridges type be used on almost all new inkjet printer from canon.

Here the reset procedure to reset waste ink counter on Canon Pixma MP145 :

1. Connect Printer to a Power source, Turn off the printer if printer on
2. With the Printer power off, press the Power button while press and hold Stop/Reset button.
3. When the Power led is light, press Stop/Reset button two times while pressing and holding the Power button.
4. When releasing the Power button and the Stop/Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
5. When the on/off lights in green, press the Stop/Reset button four times to reset wase ink counter. For other specified number pressed function listed in the table below. (Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange).
6. Unplug cable power from a power source.

To use the printer together, we can take advantage of the printer sharing feature in Windows 10.When working in an office or a room that uses the same network, either LAN or Wi-Fi, all computers in that place can use a printer connected to it. network without having to use cables.

Sharing the printer over the network will be more practical and effective because the job of printing documents becomes easier. You can print documents directly from the computer or laptop that you are using without having to plug the USB cable into the printer.

If in a room there are several computers that are used by different people, then each of these computers can use a printer together. The condition is that both the computer and printer must be connected to the same network, either via a LAN cable or Wi-Fi.

On this occasion, Winpreso will provide a step-by-step tutorial on how to share printers in Windows 10. You can practice it yourself in the office or at home where you work.

How to share printers in Windows 10 via a wired LAN and Wi-Fi network

1. Turn on Network Discovery and File and Printer Sharing

The first step that must be done is to turn on the Network Discovery feature, this feature functions so that computers can be found and connected to other computers or devices on a network.

Second, also activate the File and Printer Sharing feature to share the printer that we use with other computers connected in the same network.

You do this by going to the Control Panel> select Network and Sharing Center> select Change advanced sharing settings> check Turn on network discovery> check Turn on file and printer sharing> Save changes

2. Share the printer on the server computer

On the server computer (the computer that is sharing the printer) open Control Panel> Devices and Printers> Right click on the printer you want to share> select Printer Properties.

Notice in the Properties window, click on the Sharing tab> click the Change Sharing Options button> check Share this printer> name it as you wish> click OK.

Also check the option Render print jobs on client computers.

You can name the shared printer with a free name, but it's better if you give the printer type name or location or other description to make it easier to identify which printer to use.

3. Add a printer on the client computer

The next step is to add a printer that is already shared on the client computer. After you have done the two steps above, the printer should be network ready and ready to be used by other computers.

To add a new printer, go to Control Panel> Devices and Printers> Add printer.

Windows will scan, after which a list of printers on the network will appear ready for use.

Click on the printer that will be used and then click the Next button.

4. Print the document. Print a test page

After pressing the Next button in the above step you only need to wait a moment for the computer and printer to connect successfully.

If successful, a new window will appear with a button to print the document to test whether the printer is functioning properly.

Click on the Print a test page button and see if the printer can start printing the document. If you have click the Finish button.

5. The printer has successfully connected to the computer via LAN and Wi-Fi

Done, until here we have succeeded in sharing the printer on Windows 10.

Then you just need to replace the printer that is used when printing documents in applications such as word, excel, pdf, and others with this printer. The printer will appear with the name you gave it.

How to connect a printer via network in Windows 10

To add a new printer that has been shared from the network in Windows 10, there are other ways you can use it. The condition is that the printer must be in a "shared" state, meaning that it is ready to be used by other computers connected to the network.

Follow these steps:

1. Click the Windows button
2. Type "printer"
3. Select the Printers and Scanners menu
4. Click on the Add a printer or scanner button
5. Wait for the list of printers sharing on the network to appear
6. Click the printer that you want to use
7. Click Next
8. Follow the steps to Finish

How to connect a printer via IP Address in Windows 10

We can also use the IP address to connect the printer via LAN and Wi-Fi networks in Windows 10.

The trick is to access the shared directory on the server computer using the IP address and then connect the shared printer from there.

Follow these steps to share the printer via IP Address:

1. First, know how many IP addresses of computers that share the printer (server)
2. Press Windows key + R on your keyboard, then type the IP address of the server computer.
3. Click the OK button
4. We will enter the Shared directory window (it looks like windows explorer)
5. Find the name of the printer sharing there
6. Right click on the printer
7. Select Connect
8. The install process will begin, wait for it to finish
9. Printer is ready to use
10. Do a test print document to make sure the printer is functioning properly

Resolve undetected printer and print job jams

When sharing a printer in Windows 10, there may be problems such as a printer that is not detected or does not appear so that it cannot be connected.

To fix this, make sure you have enabled the Network discovery and File and printer sharing features as described in the steps above.

Next is to make sure that the computer and printer must be connected to the same network, either using a LAN cable or Wi-Fi.

The second problem is printer jam. When printing documents through the printer sharing feature in Windows 10, you may experience printer problems that cannot print.

Usually an error message will appear such as print jobs cannot be sent or others. This problem occurs quite often and to solve it is not difficult.

How to solve a print job jam in Windows 10:

1. Open the Control Panel
2. Select Devices and Printers
3. Double-click the printer with problems
4. Press CTRL + A button to select all existing print jobs
5. Select Cancel all document or press the delete key on the keyboard
6. Close all windows
7. Try printing the document again

After doing the steps above, the printer should return to normal. Just try a test to print a document and see if the printer is good again.

This is the tutorial on how to share printers in Windows 10 via LAN or Wi-Fi networks and some solutions to solve problems that often occur. Hope you can help.

Reset Printer Canon MP140, MP160, MP180, MP210, MP220, MP460, MP470, MP500, MP510, MP520, MP530, MP600, MP610, MP800, MP820, MP810, MP830, MP960, MP970

1. Start with printer off
2. Press and hold resume Button (triangle in the circle) and click “Power” button. green led should be on
3. hold the Power button, release Resume Button.
4. Without releasing the Power Button, double click “Resume” button and then release Both Buttons.
5. Click “Resume” for four times then click “Power” button, to confirm the selected action (reset counter absorber).
6. Turn off the printer and turn on again

1. Disconnect the power cable
2. Hold down power button
3. Reconnect the power cable
4. With the power button still down, press twice the “Cancel/Stop” red button
5. Release the power button
6. The printer is now in factory mode…(wait about 30 seconds until it says “idle”)
7. Press the down arrow (next to the “OK” button) until it says “Shipping Mode 1”
8. Press the “OK” Button
9. Now with it displaying “Without Cleaning” press the power button
10. A test page should print
11. Now open cover
12. Disconnect the power again
13. Take both cartridges out like normal
14. Close cover
15. Reconnect power cable
16. Press power button
17. Replace cartridges

1. Disconnect the power cable.
2. Hold down On/Off button.
3. Reconnect the power cable.
4. With the power button still down, press the Stop/Reset button twice.
5. Release the On/Off button.
6. The printer is now in factory mode (wait until idle is displayed)
7. Press the right arrow button (next to the OK button) repeatedly until Shipping Mode 3 is displayed.
8. Press the OK Button
9. Wait until “Without Cleaning” is displayed and then presss the Stop/Resetbutton once.
10. A test page should print.
11. Open the cover. (the cartridges should position themselves at the far left – the cartridge removal location)
12. Disconnect the power cable.
13. Remove both cartridges.
14. Close the cover.
15. Reconnect the power cable.
16. Press the On/Off button.
17. Wait until a Replace Cartridges message is displayed. Now insert the cartridges.
18. Wait until the printer is operating in its normal mode. The display shows the normal start menu (ie: Copy).

• Check by going to printer ->properties -> maintenance -> view printer status